Vaporesso Swag Kit Product Review Installation and Usage
The packaging in the Vaporesso Swag kit is as beautiful as ever in most Vaporesso products. In the first layer of the box you will receive Cam with mod, atomizer and a spare coil. Under the plastic end of the box is a high-quality USB cable. The first impression in the Swag Kit is very similar to an Eleaf Pico or Smok Baby Alien mode. It is one of the only 18650 field modes with an upgraded battery cover. It is a nice form factor and I liked the design. The good thing about this mode is that, unlike the other two I mentioned earlier, Vaporesso tends to use a much better chipset. Vaporesso Swag kit can be checked from the vaporesso site with the inquiry card that is included in the original package. The package contains English instruction manual. As there is no distributor of electronic cigarette products in our country, it is not possible to send with Turkish user manual.
Vaporesso Swag Kit has 10 seconds ignition protection, Short Circuit Protection, Low Voltage Protection, Overload Protection, Over-temperature Protection, Atomizer protection as many devices as protection factors of electronic cigarettes.
In this table, the VW mode of the device according to the watts are specified. For the GT2 coil that comes with the Vaporesso Swag attached, the 30w is recommended for the first start. Vaporesso GT CCELL is a ceramic coil unlike other coils. The aroma will taste better but the steam is at a lower level.
Normal mode is generally preferred, soft mode is preferred for these liquids with higher PG and higher nicotine values, while High mode is preferred for lower nicotine levels and higher Pg ratios.
High Mode: It is preferred for strong hit, if the watt value you use is 50W, when you press the ignition button, it starts as high as 10%, it comes to 50w after 1 second and it gives you faster and more abundant steam. In general, high VG low nicotine value is the choice of users.
Normal Mode: The most preferred mode selection gives constant watts.
Soft Mode: is the preference of those who like soft drink like the name, the watt value you use is 50W when you press the ignition button starts at a low value as 10% comes after 1 second and provides a comfortable drink in high ohms coils in high pg and nicotine ratio is the choice of users. Throat beat is better for high PG liquids.
Starting at the beginning of the mode, we have an upgraded battery cover. It goes out quite a lot from the top plate of the mode. The battery cover is black and has a little jagged around it. Threading in the battery cap is very smooth, especially at the teeth. Inside the battery cover, we have a negative battery orientation mark. There is also a positive battery orientation mark inside the battery tube. The battery contact at the bottom of the tube is gold-plated and spring-loaded. At the top of the mode, just opposite the battery cover is the 510 connector. As with most Vaporesso modes, the 510 connection in this mode is quite good. It has a spring-loaded gold-plated 510 pin and is firmly in contact with the atomiser. Because of the battery cover, anything larger than 22 mm will not fit in this mode. If the 3.5ml liquid capacity is not sufficient, the liquid capacity can be increased with bubble glass. The liquid capacity of the electronic cigarettes of European standards in electronic cigarettes is limited to 2 ml. The Vaporesso swag is used for the menu of electronic cigarettes plus and minus buttons are stuffy and responsive. They are embedded in a little mode, so it is very difficult to change the settings unintentionally while carrying or using them. Under the Vaporesso Swag Mode, we have some battery discharge arranged in a circular pattern. This pattern occurs on both sides of the mode base. Each circular pattern has 6 vents. Most cigarette users want to see these ventilation ducts on their devices.
In front of the Vaporesso Swag Mode, there is a 0.91 inch OLED display. It's a nice size display for a mod like this. It's smaller than the rival smok al85, but the screen size doesn't really matter, we're adjusting the watts after installing the coils and checking the battery status for a long time. .You can see your resistance, battery life, watts, preheating and applied voltage on the screen. It is a lot of information for such a small screen.
Swag mode uses Vaporesso's 2.0 Omniboard proprietary chip. This chip is fired as low as 0.05 ohms and as high as 5 ohms. It has a maximum voltage of 8.5 volts and a temperature control range of 200 to 600 Fahrenheit. The chip also has a full temperature control package. Ni, Ti and SS can make TC. It also has a temperature control curve feature and a TCR function with two memory slots and a watt curve feature. I absolutely love the smart VW mode. I think it's a big gain for beginners. In this mode, when you plug in an atomizer in power mode, it gives you a recommended wattage. This is great for new users who don't know where to start. It also has a bypass mode, and if you want, you can only operate it in power mode.
Overall, I would say that the design of this vaporesso swag mod is very compact and good looking. It definitely has a nice feel and weight. Although the side panels appear to be made of plastic, they don't feel cheap at all. I love the way this mode combines the two-tone look and color combinations. The mode is available in black, blue, orange and stainless steel.
The tank in this kit is the NRG SE 22 mm Sub Ohm atomizer. A smaller version of the NRG tank used in Vaporesso Revenger-Switcher models. Like the larger version, it has an overfill system. There is an arrow on the top cover. Push in the direction of the arrow and slide the tank to the left to open. Very similar to the top fill of a Smok Baby Beast genre. The only difference is that the top cover slides left and right, not right and sideways. This tank holds 3.5 ml elikit. The bottom of the tank of the Vaporesso NRG SE atomizer has a lower air flow. The bottom of the tank has two airflow slots positioned opposite each other. The air duct is smooth and easy to adjust. This is a bottom air tank. At the bottom of the atomizer you will see a Vaporesso brand as well as a serial number. The 510 pin in the NRG tank is silver plated and the threads around the 510 are stainless steel. The floss is very smooth and provides trouble-free operation in other modes I have used so far.
Favorite Menu Operations:
On / Off: To turn on the device, press the fire button 5 times in quick succession within 2 seconds. Likewise, after 5 prints the device will be switched off.
Display: After power on, OLED voltage resistance, battery level, temperature, output voltage etc. Images. Press the fire button at any time, the display lights up with the main menu.
Automatic atomizer recognition: The mode will read the coil resistance as soon as the connection is detected. When a kanthal coil is used, it will also recognize the coil type, the mode will switch from TC to watts.
Locking / unlocking the adjustment buttons: When the device is switched on, if the mode and + buttons are pressed simultaneously for two seconds, the up and down buttons are locked and the message SYSTEM LOCKED appears on the display. Likewise, pressing the up and mode buttons can be locked and the display shows SYSTEM UNLOCKED.
Change display mode: Keep pressing the up and down keys simultaneously for two seconds, the screen display will rotate 180 degrees.
Change the vaping modes: Press and hold the mode button for three seconds to toggle between VW (H / N / S) / VT (Ni200, SS, Ti) / TCR / BYPASS / CCW / CCT.
Charging: With Quick Charging System and sync charging system. To fully charge the battery, connect the USB cable to charge the battery, the OLED display battery (0%, 20%, 50%, 80% and 100%) and the Remaining Charge Time. The remaining Charge Time will be displayed every 10 minutes. And the screen will remain lit while charging.
Locking / Unlocking resistance: In TC-Ni / TC-Ti / TC-SS / TCR (M1, M2) Mode, press the - and mode button at the same time, lock / unlock 2s resistance level. Screen Insert a new atomizer will not change the locked resistance. Automatic atomizer recognition: For better temperature control effect, the mode will ask the user if a new atomizer is installed. OLD LOAD: -, NEW LOAD: + will appear on the screen. If a new atomizer is installed, press the + "key, the mode will read the new resistor; if not, press the - key, the mode will read the locked resistor.
Smart mode ON / OFF: As an advanced Variable Watt mode, Smart VW can be switched on and off in the main user manual and does not affect VW (H / N / S). Enter Smart ON / OFF and press Yes or No to confirm.
Display Timeout: The timeout setting can be set from 3 seconds to 60 minutes. Enter the Screen Timeout and set the time up or down as desired.
Default: You can reset to the default settings by entering the default and pressing YES.
